Skip to contentSkip to conversation

x86-power-control question: front panel buttons dont work

DISCUSSION Nikita Pavlov 2 participants 6 messages Apr 30, 2022 – Jul 19, 2022 3 messages not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): MW3PR11MB4732097DE3322E07CD2F99C2A3FD9@MW3PR11MB4732.namprd11.prod.outlook.com

#3 lore raw

Hi Jason, thank you for your response. In my platform I have power-control gpios in GPIOD group like this:
/*D0-D7*/ "POWER_BUTTON","POWER_OUT","RESET_BUTTON","RESET_OUT",
Also I configurate pass-through mode in dts:
        pinctrl-names = "pass-through";        pinctrl-0 = <&pinctrl_gpid0_default                            &pinctrl_gpid2_default>;
After update and reboot platform I have same problem - front panel buttons dont enable (front panel buttons dont enable if I use x86-power-control module or manually set gpio values by gpioset utility).But if I dont use any impacts on gpio (disable x86-power-control module and dont use gpio utilities like gpioset/get) front panel buttons work well. What are your assumptions about this ?

 --
Best regards,
Nikita Pavlov,
NUST MISiS Student

    четверг, 28 апреля 2022 г., 23:01:13 GMT+3, Bills, Jason M <[email protected]> написал(-а):  

<!--#yiv3781498404 _filtered {} _filtered {} _filtered {}#yiv3781498404 #yiv3781498404 p.yiv3781498404MsoNormal, #yiv3781498404 li.yiv3781498404MsoNormal, #yiv3781498404 div.yiv3781498404MsoNormal {margin:0in;font-size:11.0pt;font-family:"Calibri", sans-serif;}#yiv3781498404 a:link, #yiv3781498404 span.yiv3781498404MsoHyperlink {color:blue;text-decoration:underline;}#yiv3781498404 span.yiv3781498404EmailStyle18 {font-family:"Calibri", sans-serif;color:windowtext;}#yiv3781498404 .yiv3781498404MsoChpDefault {font-size:10.0pt;} _filtered {}#yiv3781498404 div.yiv3781498404WordSection1 {}-->
Hi Nikita,

In the hardware, we have the power button routed through a GPIO pass-through on the Aspeed chip.  If that pass-through is disabled, it will prevent the physical front panel button signal from getting past the BMC.  That is the first thing I would check.

Also, it is better to send these kinds of questions to the OpenBMC mailing list as there may be others in the community in a similar situation.

Thanks,

-Jason

From: Nikita Pavlov <[email protected]>
Sent: Thursday, April 28, 2022 8:58 AM
To: Bills, Jason M <[email protected]>; [email protected]
Subject: x86-power-control question: front panel buttons dont work

Hi, I user x86-power-control module for my test intel platform. Its module works in webui but front panel physical buttons doesnt work. I think that it interface describe in this fragment https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072 but I cant understand this logic.

Say me pls, whyfront panel buttons dont work ?

--
Best regards,
Nikita Pavlov,
NUST MISiS Student

#4 lore raw

Hi Nikita,

Quoted 9 lines · Nikita Pavlov

Hi Jason, thank you for your response. In my platform I have power-control gpios in GPIOD group like this:

/*D0-D7*/ "POWER_BUTTON","POWER_OUT","RESET_BUTTON","RESET_OUT",

Also I configurate pass-through mode in dts:

        pinctrl-names = "pass-through"; pinctrl-0 = <&pinctrl_gpid0_default &pinctrl_gpid2_default>;

Could you please share what is your BMC hardware version?

Quoted 5 lines

After update and reboot platform I have same problem - front panel buttons dont enable (front panel buttons dont enable if I use x86-power-control module or manually set gpio values by gpioset utility). But if I dont use any impacts on gpio (disable x86-power-control module and dont use gpio utilities like gpioset/get) front panel buttons work well.

What are your assumptions about this ?

The pass-through is set up as a mux in pinctrl. If I remember correctly, the output pin has GPIO output and pass-through mode as two different options in the pinctrl mux.

So, when you request the output pin using libgpiod, it automatically configures the pinctrl to disable the pass-through. You should be able to re-enable pass-through by simply releasing control of the output pin in libgpiod.

For simplicity, let's work with just the gpioset utility and not use x86-power-control. So, when you initially boot, the pass-through is working. You then use gpioset to change the output pin (which will switch the pinctrl mux and disable pass-through mode causing the front panel to stop working). When you stop gpioset, it should release the gpio and switch the mux back to enable pass-through mode for the front panel to work again.

In your test does the front panel start working again after stopping gpioset? Or does the front panel stop working from there until the next reboot even after stopping gpioset?

Thanks,
-Jason

Quoted 37 lines

--
Best regards,
Nikita Pavlov,
NUST MISiS Student

четверг, 28 апреля 2022 г., 23:01:13 GMT+3, Bills, Jason M <[email protected]> написал(-а):

Hi Nikita,

In the hardware, we have the power button routed through a GPIO pass-through on the Aspeed chip.  If that pass-through is disabled, it will prevent the physical front panel button signal from getting past the BMC.  That is the first thing I would check.

Also, it is better to send these kinds of questions to the OpenBMC mailing list as there may be others in the community in a similar situation.

Thanks,

-Jason

*From:* Nikita Pavlov <[email protected]>
*Sent:* Thursday, April 28, 2022 8:58 AM
*To:* Bills, Jason M <[email protected]>; [email protected] *Subject:* x86-power-control question: front panel buttons dont work

Hi, I user x86-power-control module for my test intel platform. Its module works in webui but front panel physical buttons doesnt work. I think that it interface describe in this fragment https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072 <https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072> but I cant understand this logic.

Say me pls, why front panel buttons dont work ?

--
Best regards,
Nikita Pavlov,
NUST MISiS Student

#5 lore raw

Hi Jason,
Front panel stop working from there until the next reboot even after stopping gpioset.
I test it with getting POWER_OUT line value and then released line like this:
#include <gpiod.hpp>
#include <iostream>
int main(int argc, char** argv){    gpiod::line line = gpiod::find_line("POWER_OUT");    if (!line)    {        std::cerr << "find line error\n";        return -1;    } try    {        line.request({"pwr", gpiod::line_request::EVENT_BOTH_EDGES, {}});    }    catch (const std::exception& ec)    {        std::cerr << ec.what();    } int state = line.get_value();    std::cout << state << '\n';    line.release();
    return 0;}

But front panel button also doesnt work with getting value. --
Best regards,
Nikita Pavlov,
NUST MISiS Student

понедельник, 2 мая 2022 г., 18:36:24 GMT+3, Bills, Jason M <[email protected]> написал(-а):

Hi Nikita,

Quoted 10 lines · Nikita Pavlov

Hi Jason, thank you for your response. In my platform I have power-control gpios in GPIOD group like this:

/*D0-D7*/ "POWER_BUTTON","POWER_OUT","RESET_BUTTON","RESET_OUT",

Also I configurate pass-through mode in dts:

          pinctrl-names = "pass-through"; pinctrl-0 = <&pinctrl_gpid0_default &pinctrl_gpid2_default>;

Could you please share what is your BMC hardware version?

Quoted 8 lines

After update and reboot platform I have same problem - front panel buttons dont enable (front panel buttons dont enable if I use x86-power-control module or manually set gpio values by gpioset utility). But if I dont use any impacts on gpio (disable x86-power-control module and dont use gpio utilities like gpioset/get) front panel buttons work well.

What are your assumptions about this ?

The pass-through is set up as a mux in pinctrl.  If I remember correctly, the output pin has GPIO output and pass-through mode as two different options in the pinctrl mux.

So, when you request the output pin using libgpiod, it automatically configures the pinctrl to disable the pass-through. You should be able to re-enable pass-through by simply releasing control of the output pin in libgpiod.

For simplicity, let's work with just the gpioset utility and not use x86-power-control.  So, when you initially boot, the pass-through is working. You then use gpioset to change the output pin (which will switch the pinctrl mux and disable pass-through mode causing the front panel to stop working). When you stop gpioset, it should release the gpio and switch the mux back to enable pass-through mode for the front panel to work again.

In your test does the front panel start working again after stopping gpioset? Or does the front panel stop working from there until the next reboot even after stopping gpioset?

Thanks,
-Jason

Quoted 47 lines

--
Best regards,
Nikita Pavlov,
NUST MISiS Student

четверг, 28 апреля 2022 г., 23:01:13 GMT+3, Bills, Jason M <[email protected]> написал(-а):

Hi Nikita,

In the hardware, we have the power button routed through a GPIO pass-through on the Aspeed chip.  If that pass-through is disabled, it will prevent the physical front panel button signal from getting past the BMC.  That is the first thing I would check.

Also, it is better to send these kinds of questions to the OpenBMC mailing list as there may be others in the community in a similar situation.

Thanks,

-Jason

*From:* Nikita Pavlov <[email protected]>
*Sent:* Thursday, April 28, 2022 8:58 AM
*To:* Bills, Jason M <[email protected]>; [email protected] *Subject:* x86-power-control question: front panel buttons dont work

Hi, I user x86-power-control module for my test intel platform. Its module works in webui but front panel physical buttons doesnt work. I think that it interface describe in this fragment
https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072
<https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072> but
I cant understand this logic.

Say me pls, why front panel buttons dont work ?

--
Best regards,
Nikita Pavlov,
NUST MISiS Student

#6 lore raw

Hi Nikita,

Sorry for the delay on this as I was on leave. Did this get resolved?

Quoted 3 lines · Nikita Pavlov

Hi Jason,

Front panel stop working from there until the next reboot even after stopping gpioset.

It sounds like something in the pinctrl muxing is not behaving as expected.

Do you use Aspeed? What version of Aspeed chip are you using? (This will help find the pinctrl info in the kernel which is hardware-specific.)

Quoted 148 lines

I test it with getting POWER_OUT line value and then released line like this:

#include <gpiod.hpp>

#include <iostream>

int main(int argc, char** argv)
{
    gpiod::line line = gpiod::find_line("POWER_OUT"); if (!line)
    {
        std::cerr << "find line error\n"; return -1;
    }

    try
    {
        line.request({"pwr", gpiod::line_request::EVENT_BOTH_EDGES, {}}); }
    catch (const std::exception& ec)
    {
        std::cerr << ec.what();
    }

    int state = line.get_value();
    std::cout << state << '\n';
    line.release();

    return 0;
}

But front panel button also doesnt work with getting value.

--
Best regards,
Nikita Pavlov,
NUST MISiS Student

понедельник, 2 мая 2022 г., 18:36:24 GMT+3, Bills, Jason M <[email protected]> написал(-а):

Hi Nikita,

Quoted 10 lines · Nikita Pavlov

Hi Jason, thank you for your response. In my platform I have power-control gpios in GPIOD group like this:

/*D0-D7*/ "POWER_BUTTON","POWER_OUT","RESET_BUTTON","RESET_OUT",

Also I configurate pass-through mode in dts:

          pinctrl-names = "pass-through"; pinctrl-0 = <&pinctrl_gpid0_default &pinctrl_gpid2_default>;

Could you please share what is your BMC hardware version?

Quoted 6 lines

After update and reboot platform I have same problem - front panel buttons dont enable (front panel buttons dont enable if I use x86-power-control module or manually set gpio values by gpioset utility). But if I dont use any impacts on gpio (disable x86-power-control module and dont use gpio utilities like gpioset/get) front panel buttons

work well.

Quoted 2 lines

What are your assumptions about this ?

The pass-through is set up as a mux in pinctrl.  If I remember correctly, the output pin has GPIO output and pass-through mode as two different options in the pinctrl mux.

So, when you request the output pin using libgpiod, it automatically configures the pinctrl to disable the pass-through. You should be able to re-enable pass-through by simply releasing control of the output pin in libgpiod.

For simplicity, let's work with just the gpioset utility and not use x86-power-control.  So, when you initially boot, the pass-through is working. You then use gpioset to change the output pin (which will switch the pinctrl mux and disable pass-through mode causing the front panel to stop working). When you stop gpioset, it should release the gpio and switch the mux back to enable pass-through mode for the front panel to work again.

In your test does the front panel start working again after stopping gpioset? Or does the front panel stop working from there until the next reboot even after stopping gpioset?

Thanks,

-Jason

Quoted 16 lines

--
Best regards,
Nikita Pavlov,
NUST MISiS Student

четверг, 28 апреля 2022 г., 23:01:13 GMT+3, Bills, Jason M <[email protected] <mailto:[email protected]>> написал(-а):

Hi Nikita,

Quoted 7 lines

In the hardware, we have the power button routed through a GPIO pass-through on the Aspeed chip.  If that pass-through is disabled, it will prevent the physical front panel button signal from getting past the BMC.  That is the first thing I would check.

Also, it is better to send these kinds of questions to the OpenBMC mailing list as there may be others in the community in a similar

situation.

Quoted 8 lines

Thanks,

-Jason

*From:* Nikita Pavlov <[email protected] <mailto:[email protected]>> *Sent:* Thursday, April 28, 2022 8:58 AM
*To:* Bills, Jason M <[email protected]

<mailto:[email protected]>>; [email protected] <mailto:[email protected]>

Quoted 6 lines

*Subject:* x86-power-control question: front panel buttons dont work

Hi, I user x86-power-control module for my test intel platform. Its module works in webui but front panel physical buttons doesnt work. I think that it interface describe in this fragment

https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072 <https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072

Quoted 2 lines

<https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072 <https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072>> but

Quoted 9 lines

I cant understand this logic.

Say me pls, why front panel buttons dont work ?

--
Best regards,
Nikita Pavlov,
NUST MISiS Student

#7 lore raw

Hi Jason,
I still have this problem. After power off board I cant run it from physical buttons.Pass-through mode configured in kernel like CONFIG_ or it comes as a kernel patch ?

I have GPIOD0 power button GPIOD1 power out. Kernel show this debug information in sysfs /sys/kernel/debug/pinctrl/1e6e2080.pinctrl-aspeed-g5-pinctrl/pingroups:
group: GPID0pin 24 (F19)pin 25 (E21)
group: GPID2pin 26 (F20)pin 27 (D20)
group: GPID4pin 28 (D21)pin 29 (E20)
group: GPID6pin 30 (G18)pin 31 (C21)
group: GPIE0pin 32 (B20)pin 33 (C20)
group: GPIE2pin 34 (F18)pin 35 (F17)......
I cant understand what it mean but in this debug file among all gpios there are only GPIOD and GPIOE gpio banks.

--
Best regards,
Nikita Pavlov,
NUST MISiS Student

    среда, 8 июня 2022 г., 18:04:16 GMT+3, Bills, Jason M <[email protected]> написал(-а):  

Hi Nikita,

Sorry for the delay on this as I was on leave.  Did this get resolved?

Quoted 4 lines · Nikita Pavlov

Hi Jason,

Front panel stop working from there until the next reboot even after stopping gpioset.

It sounds like something in the pinctrl muxing is not behaving as expected.

Do you use Aspeed?  What version of Aspeed chip are you using? (This will help find the pinctrl info in the kernel which is hardware-specific.)

Quoted 153 lines

I test it with getting POWER_OUT line value and then released line like this:

#include <gpiod.hpp>

#include <iostream>

int main(int argc, char** argv)
{
      gpiod::line line = gpiod::find_line("POWER_OUT"); if (!line)
      {
          std::cerr << "find line error\n"; return -1;
      }

      try
      {
          line.request({"pwr", gpiod::line_request::EVENT_BOTH_EDGES, {}}); }
      catch (const std::exception& ec)
      {
          std::cerr << ec.what();
      }

      int state = line.get_value();
      std::cout << state << '\n';
      line.release();

      return 0;
}

But front panel button also doesnt work with getting value.

--
Best regards,
Nikita Pavlov,
NUST MISiS Student

понедельник, 2 мая 2022 г., 18:36:24 GMT+3, Bills, Jason M <[email protected]> написал(-а):

Hi Nikita,

On 4/30/2022 7:25 AM, Nikita Pavlov wrote:
  > Hi Jason, thank you for your response. In my platform I have > power-control gpios in GPIOD group like this:
  >
  > /*D0-D7*/ "POWER_BUTTON","POWER_OUT","RESET_BUTTON","RESET_OUT", >
  > Also I configurate pass-through mode in dts:
  >
  >          pinctrl-names = "pass-through";
  >          pinctrl-0 = <&pinctrl_gpid0_default
  >                              &pinctrl_gpid2_default>;

Could you please share what is your BMC hardware version?
  >
  > After update and reboot platform I have same problem - front panel > buttons dont enable (front panel buttons dont enable if I use > x86-power-control module or manually set gpio values by gpioset utility). > But if I dont use any impacts on gpio (disable x86-power-control module > and dont use gpio utilities like gpioset/get) front panel buttons work well.
  >
  > What are your assumptions about this ?

The pass-through is set up as a mux in pinctrl.  If I remember correctly, the output pin has GPIO output and pass-through mode as two different options in the pinctrl mux.

So, when you request the output pin using libgpiod, it automatically configures the pinctrl to disable the pass-through. You should be able to re-enable pass-through by simply releasing control of the output pin in libgpiod.

For simplicity, let's work with just the gpioset utility and not use x86-power-control.  So, when you initially boot, the pass-through is working. You then use gpioset to change the output pin (which will switch the pinctrl mux and disable pass-through mode causing the front panel to stop working). When you stop gpioset, it should release the gpio and switch the mux back to enable pass-through mode for the front panel to work again.

In your test does the front panel start working again after stopping gpioset? Or does the front panel stop working from there until the next reboot even after stopping gpioset?

Thanks,

-Jason

  >
  >
  >
  > --
  > Best regards,
  > Nikita Pavlov,
  > NUST MISiS Student
  >
  >
  >
  > четверг, 28 апреля 2022 г., 23:01:13 GMT+3, Bills, Jason M > <[email protected] <mailto:[email protected]>> написал(-а):
  >
  >
  > Hi Nikita,
  >
  > In the hardware, we have the power button routed through a GPIO > pass-through on the Aspeed chip.  If that pass-through is disabled, it > will prevent the physical front panel button signal from getting past > the BMC.  That is the first thing I would check.
  >
  > Also, it is better to send these kinds of questions to the OpenBMC > mailing list as there may be others in the community in a similar situation.
  >
  > Thanks,
  >
  > -Jason
  >
  > *From:* Nikita Pavlov <[email protected] <mailto:[email protected]>> > *Sent:* Thursday, April 28, 2022 8:58 AM
  > *To:* Bills, Jason M <[email protected] <mailto:[email protected]>>; [email protected] <mailto:[email protected]>
  > *Subject:* x86-power-control question: front panel buttons dont work >
  > Hi, I user x86-power-control module for my test intel platform. Its > module works in webui but front panel physical buttons doesnt work. I > think that it interface describe in this fragment
  >
https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072
<https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072
  >
  >
<https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072
<https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072>> but

  > I cant understand this logic.
  >
  > Say me pls, why front panel buttons dont work ? >
  > --
  > Best regards,
  > Nikita Pavlov,
  > NUST MISiS Student
  >

#8 lore raw

Hi Nikita,

Sorry for the delay.

Quoted 4 lines · Nikita Pavlov

Hi Jason,

I still have this problem. After power off board I cant run it from physical buttons. Pass-through mode configured in kernel like CONFIG_ or it comes as a kernel patch ?

This looks like it may be the AST2500 since the pass-through GPIO banks are GPIOD and GPIOE.

To get pass-through working on the AST2500, we had to add some (hacky) patches. The patches are available here:
https://github.com/Intel-BMC/openbmc/blob/intel/meta-openbmc-mods/meta-ast2500/recipes-bsp/u-boot/files/0005-enable-passthrough-in-uboot.patch
https://github.com/Intel-BMC/openbmc/blob/intel/meta-openbmc-mods/meta-wht/recipes-kernel/linux/linux-aspeed/0001-Enable-GPIOE0-and-GPIOE2-pass-through-by-default.patch
https://github.com/Intel-BMC/linux/commit/7571cc86cbb4eded29aa70dbcffe84a02a22ee08
https://github.com/Intel-BMC/linux/commit/11113c101eee286a779e9fd2c106efd3c4d4ae84

Please note that we have GPIOE2 for power button and GPIOE3 for power out, so you may need to adjust some of the patches to work on GPIOD0 and GPIOD1.

Quoted 23 lines

I have GPIOD0 power button GPIOD1 power out. Kernel show this debug information in sysfs /sys/kernel/debug/pinctrl/1e6e2080.pinctrl-aspeed-g5-pinctrl/pingroups:

group: GPID0
pin 24 (F19)
pin 25 (E21)

group: GPID2
pin 26 (F20)
pin 27 (D20)

group: GPID4
pin 28 (D21)
pin 29 (E20)

group: GPID6
pin 30 (G18)
pin 31 (C21)

group: GPIE0
pin 32 (B20)
pin 33 (C20)

Quoted 6 lines

group: GPIE2
pin 34 (F18)
pin 35 (F17)
......

I cant understand what it mean but in this debug file among all gpios there are only GPIOD and GPIOE gpio banks.

Only GPIOD and GPIOE banks support pass-through, so that may be why they are the only banks listed with pin groupings.

Quoted 193 lines

--
Best regards,
Nikita Pavlov,
NUST MISiS Student

среда, 8 июня 2022 г., 18:04:16 GMT+3, Bills, Jason M <[email protected]> написал(-а):

Hi Nikita,

Sorry for the delay on this as I was on leave.  Did this get resolved?

Quoted 4 lines · Nikita Pavlov

Hi Jason,

Front panel stop working from there until the next reboot even after stopping gpioset.

It sounds like something in the pinctrl muxing is not behaving as expected.

Do you use Aspeed?  What version of Aspeed chip are you using? (This will help find the pinctrl info in the kernel which is hardware-specific.)

Quoted 17 lines

I test it with getting POWER_OUT line value and then released line like this:

#include <gpiod.hpp>

#include <iostream>

int main(int argc, char** argv)
{
      gpiod::line line = gpiod::find_line("POWER_OUT"); if (!line)
      {
          std::cerr << "find line error\n"; return -1;
      }

Quoted 3 lines

      try
      {
          line.request({"pwr", gpiod::line_request::EVENT_BOTH_EDGES,

{}});

Quoted 23 lines

      }
      catch (const std::exception& ec)
      {
          std::cerr << ec.what();
      }

      int state = line.get_value();
      std::cout << state << '\n';
      line.release();

      return 0;
}

But front panel button also doesnt work with getting value.

--
Best regards,
Nikita Pavlov,
NUST MISiS Student

Quoted 2 lines

понедельник, 2 мая 2022 г., 18:36:24 GMT+3, Bills, Jason M <[email protected]

<mailto:[email protected]>> написал(-а):

Quoted 16 lines

Hi Nikita,

On 4/30/2022 7:25 AM, Nikita Pavlov wrote:
  > Hi Jason, thank you for your response. In my platform I have > power-control gpios in GPIOD group like this:
  >
  > /*D0-D7*/ "POWER_BUTTON","POWER_OUT","RESET_BUTTON","RESET_OUT", >
  > Also I configurate pass-through mode in dts:
  >
  >          pinctrl-names = "pass-through";
  >          pinctrl-0 = <&pinctrl_gpid0_default
  >                              &pinctrl_gpid2_default>;

Quoted 5 lines

Could you please share what is your BMC hardware version?
  >
  > After update and reboot platform I have same problem - front panel > buttons dont enable (front panel buttons dont enable if I use > x86-power-control module or manually set gpio values by gpioset

utility).

Quoted 1 line

  > But if I dont use any impacts on gpio (disable x86-power-control

module

Quoted 30 lines

  > and dont use gpio utilities like gpioset/get) front panel buttons work well.
  >
  > What are your assumptions about this ?

The pass-through is set up as a mux in pinctrl.  If I remember correctly, the output pin has GPIO output and pass-through mode as two different options in the pinctrl mux.

So, when you request the output pin using libgpiod, it automatically configures the pinctrl to disable the pass-through. You should be able to re-enable pass-through by simply releasing control of the output pin in libgpiod.

For simplicity, let's work with just the gpioset utility and not use x86-power-control.  So, when you initially boot, the pass-through is working. You then use gpioset to change the output pin (which will switch the pinctrl mux and disable pass-through mode causing the front panel to stop working). When you stop gpioset, it should release the gpio and switch the mux back to enable pass-through mode for the front panel to work again.

In your test does the front panel start working again after stopping gpioset? Or does the front panel stop working from there until the next reboot even after stopping gpioset?

Thanks,

-Jason

Quoted 12 lines

  >
  >
  >
  > --
  > Best regards,
  > Nikita Pavlov,
  > NUST MISiS Student
  >
  >
  >
  > четверг, 28 апреля 2022 г., 23:01:13 GMT+3, Bills, Jason M > <[email protected] <mailto:[email protected]>

<mailto:[email protected] <mailto:[email protected]>>> написал(-а):

Quoted 10 lines

  >
  >
  > Hi Nikita,
  >
  > In the hardware, we have the power button routed through a GPIO > pass-through on the Aspeed chip.  If that pass-through is disabled, it > will prevent the physical front panel button signal from getting past > the BMC.  That is the first thing I would check.
  >
  > Also, it is better to send these kinds of questions to the OpenBMC

Quoted 8 lines

  > mailing list as there may be others in the community in a similar situation.
  >
  > Thanks,
  >
  > -Jason
  >
  > *From:* Nikita Pavlov <[email protected]

<mailto:[email protected]> <mailto:[email protected] <mailto:[email protected]>>>

Quoted 2 lines

  > *Sent:* Thursday, April 28, 2022 8:58 AM
  > *To:* Bills, Jason M <[email protected]

<mailto:[email protected]>

Quoted 1 line

<mailto:[email protected] <mailto:[email protected]>>>;

[email protected] <mailto:[email protected]>

Quoted 9 lines

<mailto:[email protected] <mailto:[email protected]>>

  > *Subject:* x86-power-control question: front panel buttons dont work >
  > Hi, I user x86-power-control module for my test intel platform. Its > module works in webui but front panel physical buttons doesnt work. I > think that it interface describe in this fragment
  >

https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072 <https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072 >

Quoted 1 line

<https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072 <https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072 >

Quoted 3 lines

  >
  >

<https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072 <https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072 >

Quoted 1 line

<https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072 <https://github.com/openbmc/x86-power-control/blob/master/src/power_control.cpp#L3072>>> but

Quoted 10 lines

  > I cant understand this logic.
  >
  > Say me pls, why front panel buttons dont work ? >
  > --
  > Best regards,
  > Nikita Pavlov,
  > NUST MISiS Student
  >